Skip to content

ChipNexus NEX Agent Connects AI Assistance to Analogue IC Design Tools

Published
Author
Nidhi Agarwal
Reads
478

ChipNexus’s NEX Analogue Agent coordinates schematic, simulation, layout and verification tasks through Virtuoso, Spectre and Calibre.

ChipNexus NEX Agent Connects AI Assistance to Analogue IC Design Tools

ChipNexus’s NEX Analogue Agent brings AI task coordination into an established analogue and mixed-signal design flow. It works with Cadence Virtuoso, Spectre simulation and Siemens Calibre physical verification, using the electronic design automation (EDA) licences and process design kits (PDKs) customers already have installed. That makes the announcement chiefly about connecting design tasks across familiar tools, rather than replacing those tools with a new design environment.

Nidhi Agarwal

The agent is part of the NEX multi-agent engineering platform, where specialised AI agents handle different stages of chip development. For analogue work, the system can set up a project, create schematics, produce layouts, launch simulations, check results and prepare reports. NEX assigns these jobs to specialised Virtuoso sub-agents, each working with tools and acceptance criteria for its task.

One workflow across design stages

Analogue and mixed-signal projects move between circuit representation, electrical analysis and physical implementation. A schematic describes component connections and intended circuit structure. Simulation tests circuit behaviour under specified conditions, while layout turns the design into physical geometry that must satisfy process constraints and preserve the intended connectivity. Those stages produce different kinds of evidence, so coordinating them can involve repeated handoffs between engineers and tools.

The image is for representation purposes only

NEX is intended to bring those steps into a shared AI-driven workflow. The Analogue Agent can open and edit schematics and layouts in Virtuoso, export netlists, run Spectre simulations and analyse their results. It can also initiate design rule checks (DRC) and layout-versus-schematic (LVS) verification in Calibre, export GDS layout data, and compare layouts with reference designs.

These functions span both circuit intent and physical implementation. A netlist provides a machine-readable representation of circuit connectivity for simulation. DRC checks layout against applicable geometric rules, while LVS checks whether the layout corresponds to the schematic. The agent’s role, as described by ChipNexus, is to coordinate work through the named EDA tools and surface the resulting checks and simulation evidence.

Nidhi Agarwal

Existing licences and PDKs remain in the flow

Using customers’ installed EDA licences and PDKs is a practical part of the product’s approach. A PDK supplies process-specific information and design rules that tools need to work with a particular fabrication process. Keeping the existing setup in use means the agent is designed to operate within the customer’s configured design environment; the announcement does not describe a separate replacement toolchain or new PDK requirement.

That distinction matters in analogue design, where device models, process rules and tool settings shape the work. An automated task still has to run against the relevant design data and configuration to produce results that engineers can evaluate. NEX’s stated integration with Virtuoso, Spectre and Calibre provides a route for the agent to act within those flows. ChipNexus does not provide performance figures, supported process nodes or specific design examples in the announcement, so the practical scope of the integration will depend on details beyond the listed tool support.

Evidence and engineering judgement

ChipNexus CEO Dan Elmhurst said that analogue design depends heavily on engineering judgement and that an AI agent in this area must show its work. He said NEX runs on the Virtuoso, Spectre and Calibre flows customers already use, and reports results against evidence from those tools. ChipNexus describes the agent as available to teams at the time of its announcement.

That emphasis on tool-generated evidence is relevant because a completed task is not the same as an accepted design. Simulation results depend on the circuit, models, conditions and setup used; physical checks likewise report against the rules and data applied to the run. Engineers still need to judge whether those inputs and results answer the design question at hand. The announcement describes automated execution and reporting, but does not claim that the agent independently certifies a design or replaces engineering review.

For design teams, the useful test will be how well the agent handles real project handoffs: whether it can carry the correct design state from schematic edits into simulation and layout checks, and whether its reports make the result easy to inspect. Its stated ability to compare layouts against reference designs adds another review path, though no details are given about comparison methods or supported reference formats.

NEX’s proposition is therefore a coordinated layer over familiar EDA work. It covers tasks from project setup through simulation and physical verification, while relying on the customer’s installed tools and process data. The next practical measure is how consistently those agents meet their task criteria and expose enough evidence for engineers to validate each result.

Source: Nidhi Agarwal · www.electronicsforu.com

Related reading