Cooling Power Electronics Across Board-Level and Large-Module Designs
- Published
- Author
- Lori O?Toole
- Reads
- 924
Mini-fan assemblies and liquid heatsinks address board-level cooling; radial-fan systems and larger liquid coolers serve high-power modules.

Cooling choices for power electronics hinge on module size, heat load and available space. Board-level assemblies can use compact fan units or liquid heatsinks, while larger modules call for high-volume air systems or liquid cooling. The design trade-offs include mounting, airflow pressure, surface tolerances, noise and the cooling circuit itself.

Power losses arise in semiconductors, transformers, converters, inductors, conductors and passive components. Their heat output depends on switching frequency, load current, voltage and the cooling method. Keeping temperatures within component specifications helps preserve reliability and service life, and can support higher power density.
Board-level cooling
Mini-fan assemblies
Conventional aluminum heatsinks can be too large and heavy for circuit-board mounting, even when they provide substantial cooling capacity. Fischer Elektronik’s LAM series mini-fan units are designed for high heat removal in a small footprint and can be mounted on or integrated into a board.

An axial fan above the assembly drives air across an extruded aluminum section. Shaped internal surfaces increase the area available for heat exchange, while the geometry is matched to the fan’s airflow and dynamic pressure. A fin structure at the back of the rectangular base conducts heat from the semiconductor into channels through which the fan pushes heated air away.
The base also provides the semiconductor mounting surface. Components can be attached with CNC-machined threaded inserts or with snap-in transistor-retaining springs. The springs’ integrated grooves hold the device against the cooling surface and allow quick assembly.
Compact liquid heatsinks
For smaller modules with higher heat losses, a liquid heatsink can remove more heat from the board area. The pictured Fischer Elektronik unit measures 40 × 10 × 30 mm (L × W × H) and is rated to dissipate ~670 W, with a 10°C difference between water inlet and outlet and a normal operating pressure of 3 bar.

The board-mounted heatsinks are stainless steel, so they need no corrosion protection when water is used as the coolant. Pressed-in soldering pins on the underside secure the unit to the circuit board, including through reflow soldering. Fischer Elektronik makes these parts by 3D printing and uses an AI-optimized internal heat-exchange structure.
Each mounting side has a separate cooling circuit. That arrangement keeps flow-pressure losses very low and allows components to be mounted on both sides of one heatsink. Devices in TO packages or multiwatt system-in-package formats can use the same groove geometry and THFU-series retaining springs described for the fan assemblies. The mounting faces are finely sanded for uniformity and low surface roughness. Custom designs, materials and features are also available.
Cooling larger power modules
Radial-fan systems
Large power modules, including different IGBT performance classes, commonly use fan-cooled assemblies with hollow-fin sections. Fischer Elektronik reports airflow rates up to 1,400 m3/h and thermal resistance just under 0.015 K/W for its high-performance aggregates using radial fan motors.

A radial fan draws air in from the side, turns its direction by 90° and sends it into the heatsink as a high-volume, high-pressure stream. That pressure capability makes radial fans suitable for hollow-fin structures that other fan types may not drive as effectively. The resulting assemblies can be larger than systems using other fan designs, so installation space remains a key constraint.
Power modules mount to a durable base plate, which spreads heat through the assembly and provides threaded anchoring points. Surface flatness and torsion matter at this interface: the source notes that a datasheet smoothness recommendation of <0.02 mm typically requires additional machining. Fischer Elektronik precision-mills semiconductor mounting surfaces to standard dimensions and wraps them for protection against damage.
Larger liquid heatsinks
Where fan assemblies bring too much weight, noise or installation-space demand, liquid heatsinks offer another route for cooling large modules. Water has a specific heat capacity of 4.182 kJ/kg·K, about four times that of air, which helps explain the heat-transfer potential of liquid systems.
These larger Fischer Elektronik heatsinks are made entirely of aluminum, including their internal 3D honeycomb heat-exchange structure. The company specifies a water-glycol mixture rather than pure water for these units. Bonded aluminum sections form the sides and semiconductor mounting faces, transferring heat into the continuously flowing coolant. Precisely milled mounting surfaces support flexible component placement with low thermal transfer resistance.
Depending on the base construction, the units can use different connection technologies and I-flow or U-flow layouts. Sealing procedures, couplings and hose systems address leakage control. In practice, choosing among these options means matching thermal performance and mounting requirements to the module’s available space, mass allowance and operating noise limits.
