Raise3D T450 and T700 FDM Printers Pair Heated Chambers With High-Flow Extrusion
- Published
- Author
- Sam Davies
- Reads
- 850
Raise3D’s T450 and T700 combine large heated build volumes with extrusion rates up to 80 mm³/s; the company also expands RMS220 capacity and adds B520 post-processing.


Raise3D’s T450 and T700 bring large, actively heated build chambers together with high-throughput extrusion, aiming to make single-piece printing more practical for oversized tooling, prototypes and production aids. The two fused deposition modelling (FDM) systems share a platform but differ substantially in build capacity: 450 × 350 × 400 mm for the T450 and 700 × 500 × 1,000 mm for the T700. Raise3D introduced them ahead of Formnext 2026.
The shared platform includes the company’s TwinFlow extrusion system, which routes two filament paths into one nozzle. Raise3D specifies speeds of up to 600 mm/s and volumetric flow of up to 80 mm³/s under its stated reference conditions. The system can also switch between two materials, allowing soluble support material or dual-colour parts. That combination is intended to address two different constraints in large-format printing: time spent depositing material and the need to make complex shapes or multi-material components.
The maximum flow figure comes from a specific test: Raise3D Hyper Speed ABS V2 filament, a 250°C nozzle temperature, a 0.4 mm nozzle and a single-wall smooth structure. Results in other prints depend on the material, nozzle, layer height, model and settings. For engineers estimating a job, that distinction matters: the reference result describes a defined test geometry, while a real part may require slower printing because of its shape or process settings.
Managing heat across large parts
Both printers use an actively heated chamber, with Air Flow Manager 2 adjusting conditions according to the material. The T450 can hold the chamber at up to 70°C, while the T700 reaches up to 60°C. Raise3D positions these settings for large ABS and nylon parts, for which chamber temperature is part of managing the print environment across a substantial build area.
For lower-temperature materials such as PLA, the system can switch to directed cooling and open an automatic top vent. This gives the machines two distinct operating approaches within the same enclosure: retaining heat for materials that call for a warmer chamber, and moving air through the build space for materials that benefit from cooling. The details of the material and part still determine which conditions are suitable.
Motion control is built around a 4MD CoreXY arrangement with four motors mounted to the frame. Raise3D says the system is designed to reduce vibration, surface ringing and the risk of layer shifts. Those issues can become more visible on large parts, where print duration and the distance travelled by the toolhead make stable motion important to surface quality and dimensional consistency.
Other shared equipment includes a 420°C fibre-ready nozzle, a build plate rated to 120°C, camera monitoring, and detection for spaghetti failures, flow problems and filament run-out. The printers also include power-loss recovery, an emergency stop, RFID material identification and mesh levelling. Raise3D lists ideaMaker as supported software.
One-piece parts and production aids
The larger build spaces are intended to reduce the need to divide a part into sections. Raise3D CEO Edward Feng points to scoliosis braces as one example: a brace that must be produced as one piece may not be suitable for splitting and bonding back together. He says an adolescent brace fits within the T450’s 450 × 350 mm build area with room to spare. The same size advantage may apply to tooling, patterns and other parts where joins create extra work or affect the required strength.
Raise3D describes the T450 as suited to jigs and fixtures, casting patterns, large prototypes and production aids. The T700 targets larger tooling, patterns and other applications that need more build space. The practical choice between them will depend on the largest part envelope and the required chamber conditions, as well as how much capacity a shop needs for arranging several parts within one build.
The company also cites cell transport trays used in power-battery manufacturing. In its example, production time fell from about 40 days to 10 days, while tray weight dropped from about 8 kg to 2 kg. Raise3D attributes both reductions—approximately 75% each—to the combined effect of build area, extrusion throughput and material choice. These figures describe the company’s application example; they are not presented as results for every tray design or manufacturing process.
RMS220 height increase and B520 finishing
Alongside the FDM systems, Raise3D has increased the available build height of its RMS220 selective laser sintering (SLS) printer through a software update. The build volume changes from 220 × 220 × 350 mm, or 17 L, to 220 × 220 × 450 mm, or approximately 21.8 L. Raise3D puts the increase in height and volume at approximately 30%. Existing RMS220 machines can receive the update without a hardware change.
The extra 100 mm of Z height can accommodate suitable components that previously exceeded the machine’s 350 mm build height. It also leaves more room to nest parts in a build. Whether that space can be used efficiently will depend on the shapes being arranged and the requirements of the particular job.
Raise3D has also introduced the B520, an automated sandblaster for polymer powder bed parts. Its enclosed workstation combines automatic blasting with air blow-off and ionisation. A manual mode gives operators access to deep recesses and shielded areas, and suitable parts can be processed as a programmed batch. The B520 is a standalone system that supports the RMS220 and equipment using SLS, MJF, SAF and HSS processes. Its standard basket has an internal volume of 24.8 L; the large basket holds 75.5 L.
The three introductions address different stages of large-part work: the T450 and T700 expand FDM build capacity, the RMS220 update makes taller SLS builds possible, and the B520 automates part cleaning after powder bed production. Raise3D lists the T450 at US$4,999 in the United States and €4,999 in Europe, with deliveries beginning by the end of December 2026. The T700 is priced at US$15,999 and €15,999, with delivery expected by the end of January 2027.